panel, paneling, wainscoting, panel wall, wall paneling, wood paneling
Wainscoting, Columns, Trim, Cornices and Molding Products in North America
"Custom Wainscot Results... Without Custom Pricing!"

home >  installing bead board      

+ ProductsWainscot & Beadboard Wall Paneled Flat Paneled Raised Paneled Bead Board
Columns Square Columns Round Columns Pilasters Double Columns Column Capitals
Cornices Symmetrical Modern Profile Georgian Profile Dentil Profile Multi Step Coffered Ceilings Curved Walls Corners
Accents and Trim Baseboards Chair Rails Casings Door Headers Door Facing
Ornaments Ceiling Medallions < 30" Ceiling Medallions > 30" Art Niches Brackets

Pricing
Shipping
Warranty
Contact

FAQ's
Installation
Photo Gallery

About
Privacy
Site Map
Contact

Contractors Welcome!

Beadboard payment optionWainscoting payment optionPaneling payment option


Testimonials

"I can't believe how much our house has changed! The comments we get from guests and friends are unending; you sure came through with your system!"

Bead Board Installation

 

Bead Board will give the room a warm comfortable feeling, its beauty lies in its simplicity. It is probably the easiest of all wainscoting to install, regardless of your skill level. Although bead board is fairly self explanatory, it still requires some instruction. This guide will give you some helpful hints and explain some often asked question, so that your installation will look professional without paying professional prices.

    Required Tools
  • Miter saw
  • Table saw
  • Tape Measure
  • Nail gun with compressor
  • Spirit Level
  • MDF Glue
  • Latex caulking
  • Spackling compound (plaster filler)

Prep work

In order to install bead board, you should start by removing the existing base board. The baseboard in newer homes will likely only be nailed; older homes may have a very hard adhesive behind both the baseboards and casings around the doors. This adhesive can be removed using a sander or by hand using a medium grit sand paper. Do not concern yourself with the finish of the sanding as it will be covered entirely with the bead board.

Measuring and Leveling

You should first determine the height of the finished installation. If you have a standard 8 foot ceiling, you should consider a finished height of 36" from floor to the top of the chair rail. If your ceiling is higher you should consider a height of 42". The bead board is shipped in 40" lengths, but it can be cut to the desired length or installed higher up the wall using a spacer at the bottom with the same thickness as the bead board, providing the bottom is no higher from the floor than the base board height.

You should always start on an inside corner. Measure the length of the wall and calculate where you will start in order that the final strip at the end of the wall will not be too narrow to nail up. Before cutting or ripping down any of the lengths, you should check the wall to see how straight the wall actually is; never assume the wall is a perfect 90 degrees. To check this you should take your spirit level and place it on the wall you will be starting from. If the wall is slightly off, draw a straight line down the wall on which the bead board will be placed using your level, this will become your new starting point, you will later cut an angled piece to fill in the gap left over.

Cutting and Nailing

Please note that there is a face and a back to each strip of bead board. Always make sure you are cutting the bead board the right way. The reason for this is simple, each strip will have a lip on both the right and left sides, one is on the face and the other lip is set further back. These lips are not interchangeable and will be used to nail one piece of board to the next.

After having determined the final height and cutting a few pieces down to size, your first strip can either be ripped on the corner side on a 45 degree angle (or the necessary angle required to create the corner) using the table saw or you can use a butt joint (no cutting, just put one edge of a strip against the face of another). The 45 degree table saw method will give you a better finish.

Always nail at an angle of approximately 45 degrees both towards the top and the bottom, creating an "x", this will fasten the board to the wall whether you hit a stud or not. Try to nail into the crease, in order to hide the nail head better. Remember to set the pressure on the compressor to between 90 - 110 PSI, this will counter sink the nail deep enough to become invisible and easy to cover later. We recommend using a 2" 18 gauge finishing nail. At this point you can either use MDF glue and nails or just nails to hold up the boards. Using your compressed nail gun, nail up your first strip.

After nailing your first piece, use your spirit level to check the top and the side for trueness. Continue repeating the steps described in the above paragraph until you reach the end of the wall. Follow these steps for the entire room using the table saw to rip the side of the boards to 45 degrees when you hit a corner.

Baseboard Shoe mold and Chair Rail

When a wall is longer than the strip of baseboard or chair rail provided, you should make a 30 degree cut into the end of the one piece and a 150 degree cut to the end of the adjoining piece. Use MDF glue and nails on this joint so as to fasten it tightly. This will give you a seamless joint that can easily be finished later.

The baseboard will be installed flush with the floor or carpet. The baseboard should be cut using a miter saw and it will be nailed in the exact same manner as the bead boards using the "x" pattern.

The shoe mold will be applied to the bottom of the baseboard to give it more width at the bottom. Normally when a hardwood or ceramic tile floor is applied, there are some gaps left for expansion and contraction, the shoe mold will help cover that gap. If you are applying bead board around windows, you should order some more lengths so that you can finish around the window casing. Shoe mold will be cut and nailed the same way as the baseboard.

The chair rail comes notched out in the back in order for it to fit flush when applied to the top of the bead board. It to should be cut with a miter saw in order to create corners. It should be checked with a level before being fastened to the wall and bead board.

MDF glue should be applied to all chair rail corners along with nails.

Sanding and Finishing

Although everything fits flush, there will be small gaps left everywhere (top of base board, top and bottom of chair rail and the top of the shoe mold). These gaps should be filled in using a paint able latex caulking (DAP is the industry name for this). Lay down a bead and clean the excess with a wet rag or your finger.

All corners and seams will be covered with Spackling Compound (plaster filler). Apply a reasonable amount and allow it to dry for an hour. After it dries, go back and sand it down using fine grit sandpaper. The sanding should be done carefully so as not to damage the wood underneath. At this point you can re-prime this area. The nail heads will have been counter sunk and easily visible to the naked eye, using the spackling go over each nail head and fill the remaining space left by the head. The nail heads do not need to be sanded, just finish them with your finger as you go along.

Your bead board is now ready to be painted. It comes primed white and ready to accept any type of paint.

Wainscot Installation, Flexible Wainscot, Paneled Wainscot

Wainscot Products

Wall Paneled Flat Paneled - MDF Raised Paneled - MDF Raised Paneled - Hardwood Bead Board Wainscot Flexible Wainscot

 

Beadboard payment optionWainscoting payment optionPaneling payment option Columns payment options
Questions?
Email Address:
Message:
* We do not share or sell your personal information. Your personal information and or email address is used strictly for replying to your questions and comments, as well as informing you of any additional information.


 

 

 

 

back to top

Wainscot / Beadboard ~ Columns ~ Cornices ~ Accents / Trim ~ Ornaments ~ Gallery ~ Installation
Pricing ~ FAQ ~ Gallery ~ Site Map

panel, paneling, columns, wainscoting, panel wall, wall paneling, wood paneling, beadboard, wainscot, ceiling panel, panel window, panel wood, material paneling, beadboard paneling, painting paneling, wainscotting, panel wainscoting, panel wall wood, interior wall paneling, home panel, panel wainscot, wainscot panel, decorative panel wall, bead board, beadboard wainscoting, interior wood paneling, decorative wall paneling, wall panelling, beadboard ceiling, wood wall paneling, panelling, wainscot design

1300 E. Desert Inn Road, Suite 210
Las Vegas, Nevada  89109
Toll Free :1 888 877 7777