|
Spectrabeam/Microbeam
FSIR
Maintenance and Component Troubleshooting
Course Outline
Course Objectives
Throughout this course the Designated Maintenance Technician (DMT) will learn how to troubleshoot and maintain the FSIR Sensor using established EGS Gauging Inc. techniques. The DMT will be able to locate and solve sensor problems with minimal support from EGS Gauging Inc. This course provides the DMT with sensor knowledge through lecture, discussion, and hands on training.
Prerequisites
The
DMT must have attended Designated Maintenance
Technician training; EGS Gauging Course 160 and must know
and understand the machine process. Duration
Classes begin on Tuesday at 8:30 AM and will conclude on Thursday.
Friday is an answer and question period for the students with the instructor.
| Course
Content |
 |
System Overview, Refresher |
|
Safety,
Refresher |
|
Ethernet Network, Refresher |
|
Operator
Console, Refresher |
|
Scanner
Frame, Refresher |
|
Full
Spectrum Infrared (FSIR) Sensor |
|
Maintenance
& Troubleshooting |
Evaluation
Each
attendee will take a 60-minute examination covering
safety issues, operational issues and common troubleshooting
procedures. Results of the exam will be available
for customer review. Upon successful completion
of the course, the attendee will receive a Course
Certificate.
Courseware
Each
attendee will receive all necessary materials
to complete the course.
Spectrabeam/Microbeam
FSIR
Maintenance and Component Troubleshooting
Course 280 Schedule
Introduction .
Brief discussion of course objectives along with
the dos and don'ts of visiting EGS Gauging.
System
Overview Refresher.
Review of each major item within the CIMLINE System
as well as a review of the Advanced Universal
Module (AUM)
Safety
Review
Review the Safety measures for use when working
in and around the CIMLINE System.
Ethernet
Network Review
Describes the Ethernet network and its role
in CIMLINE System.
Operator
Console Review
Review the console computer and console support
equipment.
Scanner
Frame Review
Deals with the sensor transport mechanism,
Scanner AUM, and the various signals present in
the scanner frame.
Full
Spectrum Infrared (FSIR) Sensor Overview
Provides a detailed explanation of the FSIR
Sensor provided by EGS Gauging.
FSIR Configurations
Explains the different configurations of FSIR
sensors provided by EGS Gauging.
FSIR Detector
Explains the use of the FSIR detector in
web measurement.
Digital Signal Processor - MSP
Discusses the configuration of the Digital
Signal Processor (DSP) in the MicroEnhanced Signal
Processor
Parallel Signal Processor - MSP
Component level discussion of the MSP Parallel
Signal Processor (PSP).
Multi-Functional Power Supply
Component level discussion of the FSIR Power
Supply
Concepts of FSIR Calibration
Comprehensive discussion of how the FSIR
sensor measures the process web.
Fundamentals of FSIR Calibration
Overview of the FSIR calibration process.
Standard Sample Routine
Provides a discussion of the FSIR Sample
Check routine as well as practical experience.
Air Scan Test
Shows the DMT how to verify scanner frame integrity
using the FSIR sensor.
Sensor Diagnostic Routines
Explains the various displays used to diagnose
problems with the FSIR sensor.
FSIR Source Lamp Replacement
Takes the student through the steps necessary
to restore proper measurement after a source lamp
change.
Troubleshooting
Practical experience in diagnosing and correcting
problems with the FSIR sensor.
EXAM
Course
Registration
CClasses are held at EGS Gauging Inc. Reservations are on a first come first serve basis and must be made no less than two weeks before the scheduled class. For reservations contact the EGS Gauging Inc Customer Service Department at (800) 366 – 2533 or FAX your request to (978) 667 – 4146, Attention Tricia Muzerall or Jim Judkins
Course
Cost:
$2750.00 per person, all others attending
the same class at $250.00 discount. Course cost does not include travel and
living expenses.
Cancellations:
There will be a 20% cancellation fee applied
to all students canceling within three weeks of
a course, and a 50% fee for all "no-shows."
Reschedule:
EGS Gauging Inc. reserves the right to reschedule a class if there are less than 3 participants.
|
